Search
Use the search bar or filters below to find any TAPPI product or publication.
Filters
Content Type
Publications
Level of Knowledge
Collections
Journal articles
Magazine articles
Editorial: TAPPI Journal reinstates the “Technical Brief” short-form research paper, TAPPI Journal June 2019
ABSTRACT: For many years, TAPPI Journal (TJ) accepted submissions of “Technical Briefs” (also known as Technical Notes or Brief Notes) in addition to the full-length papers peer-reviewed papers that you have typically seen in more recent years. The TJ Editorial Board is once again accepting these short-form papers, as readers may have noticed in the last issue with publication of Tom Lindstrom’s short nanocellulose re-view (TAPPI Journal 18[5]: 308[2019]). Another Technical Brief appears on p. 391 of the current issue.
Journal articles
Magazine articles
The evolution of reel statistical methods, TAPPI Journal June 2019
ABSTRACT: Multiple statistical methods for calculating the variance partition analysis (VPA) of reel data have existed for decades. In the paper industry, VPA is also commonly known as reel statistics. VPA commonly consists of total variance (TOT) that is then divided into three components: cross direction (CD), machine direction (MD), and residual (RES). A common mathematical procedure is referred to as ANOVA (analysis of variance). TAPPI Standard Test Method T 545 “Cross-machine grammage profile measurement (gravimetric method)” addresses paper testing and includes the ANOVA equations that have also been used to analyze scanning data.In the 1990s, TAPPI published TIP 1101-01 “Calculation and partitioning of variance using paper machine scanning sensor measurements,” which contained simple formulas that were easy to implement and could be used by a nov-ice to generate statistics on a spreadsheet. All involved quality control system (QCS) suppliers agreed to support this common method in their QCS. TIP 1101 was recently revised, and this paper concerns the analysis of data collected from a scanning sensor in a QCS and the creation of a common method for the calculation of reel statistics by TAPPI’s Process Control Division.
Journal articles
Magazine articles
Sources, collection, and handling of noncondensible gases in modern kraft pulp mills
ABSTRACT: This work describes and discusses sources of noncondensible gases (NCG) in modern kraft pulp mills and modern NCG collection from process units where odor emissions can occur if these gases are released to the surroundings. A mill-wide overview of NCG sources and collection in modern pulp mills is provided. Using modern practices, malodorous gases can be collected to the extent that a pulp mill is essentially odor free. The key to limiting complaint-causing odors is prevention of these emissions during process disturbances, equipment malfunctions, operator errors, and other unforeseen occurrences.
Journal articles
Magazine articles
Size distribution analysis of microstickies treated by enzyme mixtures in papermaking whitewater, TAPPI Journal March 2019
ABSTRACT: Microstickies present a formidable challenge for papermakers. Many strategies have been explored o control them. Enzyme treatment is a promising technology, but the mechanism of its action has not been determined, thus inhibiting further application of this new technology. This study investigated characteristics and size distributions of microstickies treated by esterase-cellulase mixtures. Determination of particle size and number was accomplished using a modified flow cytometer, which combined streaming capillary flow, laser-based particle size analysis and fluorescent dye tracing. The results showed that treatment of samples with enzyme mixtures induced size reduction of the larger microstickies. This effect was most dramatic for 1:1 ratios of esterase to cellulase. The treated particles were more stable than untreated ones. The smaller microstickies treated with some ratios of esterase and cellulase tended to aggregate over time.
Journal articles
Magazine articles
Controllable anisotropic properties of wet-laid hydroentangled nonwovens, TAPPI Journal March 2019
ABSTRACT: For nonwovens, fiber orientation distribution is an important structural characteristic that directly influences the anisotropic properties of the materials. Different Vslurry/Vbelt ratios were adopted to fabricate nonwovens during the wet-laid process. The results indicated that fiber orientation distribution of nonwovens can be regulated by adopting different Vslurry/Vbelt ratios owing to the web-forming principle of wet-laid techniques. Mechanical tests showed that both wet and dry tensile strength of nonwovens in different angle directions present anisotropy under different Vslurry/Vbelt ratio parameters. A liquid spreading distribution experiment proved that liquid spreading length and area of nonwovens could be manipulated using different Vslurry/Vbelt ratios in the fabrication process. Therefore, specific anisotropic properties of wet-laid hydroentangled nonwovens can be realized by controlling the process parameters for particular end-use applications.
Journal articles
Magazine articles
Editorial: The changing face of the coated paper industry, TAPPI JOURNAL January 2018
Editorial: The changing face of the coated paper industry, TAPPI JOURNAL January 2018
Journal articles
Magazine articles
Editorial: Remembering Phil Clark: A Coating “Master Man”, TAPPI JOURNAL July 2018
Editorial: Remembering Phil Clark: A Coating “Master Man”, TAPPI JOURNAL July 2018
Journal articles
Magazine articles
Impact of fiber structure on edge-wicking of highly-sized paperboard, TAPPI JOURNAL August 2018
Impact of fiber structure on edge-wicking of highly-sized paperboard, TAPPI JOURNAL August 2018
Journal articles
Magazine articles
Editorial: PaperCon: A ten-year journey of papermaking excellence, TAPPI JOURNAL September 2018
Editorial: PaperCon: A ten-year journey of papermaking excellence, TAPPI JOURNAL September 2018
Journal articles
Magazine articles
Editorial: Special pulping and engineering issues of TAPPI Journal yield important recovery cycle research, TAPPI Journal June 2024
ABSTRACT: The June issue of TAPPI Journal, which is dominated by recovery cycle topics, is the last PEERS issue organized by Dr. Peter Hart, the former editor-in-chief who passed away this past May. Peter, who was heavily involved with TAPPI’s Pulp Manufacture Division and various pulping-related committees, also started working with conference technical program planning starting in 2005 with the Engineering, Pulping and Environmental (EPE) Conference, which was the precursor to the more recent Pulping, Engineering, Environmental, Recycling and Sustainability (PEERS) Conference. He was also involved with other conference planning, including that for the International Pulp Bleaching Conference. In addition, Peter was a yearly attendee of such conferences starting as far back as 1990.
